An under-sink filter is one of the more approachable home water projects. The housing mounts to the cabinet, the cartridge snaps or threads in, and two lines connect it to the cold supply. The hard part is rarely the filter. It is the plumbing it has to tie into: the shutoff valves, the supply lines, the faucet and the space under the sink. Before you buy anything, check those four things, because they decide whether this stays a homeowner job or becomes a call to a plumber.
Check the shutoff valves first
Turn the cold shutoff valve under the sink through its full range, slowly, while you watch the stem and the body. A valve that turns freely, closes all the way and does not drip around the stem can usually be trusted to isolate the line for the install. A valve that is stiff, will not fully close, or weeps when you move it is a separate repair. Do that repair before you mount anything, because a valve that fails during the install means shutting off water to the whole kitchen while you work on a wet cabinet.
Also note what the valve is connected to. Flexible supply lines with compression or push-fit fittings are typical under sinks. If the supply is rigid pipe, soldered, or an unfamiliar fitting, the job moves toward the plumber column.
Confirm the faucet and the cabinet
Many point-of-use units need either a dedicated filtered faucet or a diverter that sends some water to the filter and the rest to the standard spout. Look up your faucet model and confirm whether it has a mounting hole, a diverter option or a separate filtered spout. If the answer is no, the job now includes a faucet decision, and that is a bigger question than the filter.
Measure the cabinet. Check the space for the housing, the clearance to swing the cartridge out, and whether the unit crowds the drain trap or the garbage disposal. A housing that sits on the trap or blocks the cabinet door is a sign the install needs a different location or a different unit.
What you can do yourself
A homeowner with basic hand tools and a little patience can usually handle the mounting bracket, the cartridge installation, the flush step and the leak check. Follow the manual on thread tape, plumber's putty and fitting sequence. Tighten compression fittings snugly by hand plus a small turn with a wrench, not hard. Over-tightening is the most common way a new fitting starts to weep.
Flush the cartridge the way the manual describes before you connect it to the faucet, usually by running cold water through the housing into a bucket for the stated time. Skipping this step is a common reason for early cloudiness or a loose carbon particle at the first glass.
Where to hand the job off
Hand the job off when the shutoff valve will not close fully or leaks, when the supply is rigid pipe that needs cutting or soldering, when a new faucet hole or countertop change is required, or when the manual or local rules say the connection needs a licensed plumber. Local building offices can tell you whether a permit applies to your install, and that answer is worth getting before you start rather than after. If the water heater or a branch line has to change, treat that as a full plumbing job, not a filter install.
Questions to ask before you hire
Ask the installer to put the scope in writing. Does the quote include the shutoff valve if it fails the test, the faucet adapter, the leak check, and the first cartridge flush? Ask who is responsible for a leak at the new connections and for how long. Ask whether the installer will follow the manufacturer's instructions and leave the manual with you. Ask for the faucet model in advance so the quote does not depend on a guess. A short scope that names these items will tell you more than a low total.
The leak check and the first week
Turn the water on slowly, not all at once, and watch every connection. Dry a joint with a paper towel and check it again after an hour and once more the next day, because some leaks show only when the line is under full pressure for a while. Check the cabinet floor for moisture. Run the faucet until the first water runs clear, and write the install day on the housing label so you know when the cartridge went in. If a connection still drips after a careful retighten, stop and call the installer or a plumber rather than forcing it.
For a comparison of local providers and what their quotes should cover, see the regional index of home water treatment providers, and for how those providers are evaluated, see how we rate water treatment providers.